Secondhand 80W CO2 Laser Engraving Cutting Marking Machine Engraver w

Description OMTech 80W CO2 Laser Engraver Combining ease of use with advanced capability, this intuitive 80W CO2 laser engraver delivers professional results at a fraction of the cost. Equipped with a powerful 80-watt water-cooled laser tube, high-precision stepper motor, and a top-quality Digital LCD control board, it features our largest engraving surface (28" x 20") with a height-adjusting lift table and dual pass-through doors to accommodate oversized and irregular-shaped objects, making it one of our most highly capable engraving machines. Simply plug in the USB connector to your computer system and you’re ready to start your laser engraving story! Check out our many Accessories and Parts to go along with your laser machine! Features Digital Controller The intuitive control panel with a digital display allows complete control of the laser head, pausing and stopping projects, adjusting laser power and speed settings, file viewing, and project framing via Windows-compatible RDWorks v8. Four-Way Pass-Through The four-way pass—32¾″×3⅞″ front & back and 19⅝″×⅝″ on either side—allows you to feed material into the workbed from any direction, letting you cut materials larger than the bed size by sliding them across the engraving table. Honeycomb and Knife Beds This engraver includes 2 workbeds—one honeycomb and one aluminum blade—for handling projects large and small with maximal safety and efficiency. High-Performance DC Tube Our 1250 mm CO ₂ laser tube provides 80W of power for up to 4000 hours or up to 8000 hours of operation when consistently used at lower settings. Easy Hookup One USB port reads flash drives while the other connects directly to your PC via dedicated cable. The Ethernet port allows you to work remotely online. Linear Rail Guiding System Equipped with X and Y stepper motors for efficient power transmission between the guide rails with high precision and long service life. Red Dot Guidance A red dot pointer mounted on the laser head quickly indicates engraving points, marks the machine’s path, and identifies positioning sizes, allowing an effortless project setup process. Adjustable Laser Nozzle The laser nozzle can extend downwards up to 1.75” or be fully retracted, allowing more control over different focal distance setups. Built-in Air Assist A pre-installed air compressor guides a pressurized air stream through the laser head nozzle to displace debris, heat, and combustible gases from the engraving surface and laser beam path, keeping your workbed cleaner and engravings more precise. Spacious Work Area The 20″ × 28″ (500×700 mm) workbed gives you plenty of space to work on wood, rubber, plastic, paper, fabric, leather, ceramics, tile, fiberglass, marble, stone, and more—even before you open the integrated pass-through doors that permit you to work on even larger pieces! Water Cooling System Pre-installed hoses along with the included water pump allow for a fast and easy setup. Only use with distilled water, ensuring it stays between 60–70°F (16–21°C). Water Flow Sensor A pressure flow sensor monitors water flow throughout the laser engraving process and prevents the laser from firing if water stops circulating through the laser tube. Digital Laser Power Supply A crystal-clear LCD display provides real-time information about the device's electric current and autocorrects faults, reducing damage to your laser tube and power supply in the rare case of improper ammeter connections. Safe Observation The transparent acrylic window's sepia filter allows you to observe your engraver in action, as the tint blocks the laser beam and protects your eyes. Cover Protection The laser automatically stops engraving, cutting, or marking when the workbed's cover is opened for your safety. Close the cover and press Start to resume your work. Emergency Stop The E-Stop safety button immediately stops the machine in case of emergency. High-Precision Laser Head The industrial-grade laser head delivers a stable laser beam over the long service life of the machine, while the red-dot locator helps to quickly indicate engraving points and marks the engraving path, allowing effortless setup and operation. Specification MPN: MF-2028-80 Model: SH-G570 Input Power: 110V/60Hz AC Processing Area: 20×28 in. (500×700 mm) Max. Engraving Depth: 0.35 in. (9 mm) Workbed Adjustment: Manual Workbed Height Range: 9 in. (230 mm) Front/Back Pass Size: 32.87×3.94 in. (885×95 mm) Side/Side Pass Size: 19.69×0.71 in. (500×18 mm) Max. Engraving Speed: 23.6 ips (600 mm/s) Max. Cutting Speed: 15.7 ips (400 mm/s) Included Software: RDWorks 8, CorelLaser Graphic Operating Modes: Optimized Raster, Vector, and Combined Transfer Interface: Flash Drive, USB Cord, Ethernet Cord Net Weight: 297 lb. (135 kg) Machine Dimensions: 47.2×33.9×27.6 in. (120×86×70 cm) Laser Tube Specs Rated Power: 80W Laser Tube Model: EFR F2 Laser Wavelength: 10.6 μm Laser Tube Diameter: 3.2 in. (80 mm) Laser Tube Length: 49.2 in. (1250 mm) Laser Tube Warranty: 3 months "Exp. Service Life: at <40% / 40–70% / >70% Power: "7000–8000 / 5000–6500 / 3000–4000 hr. Lens & Mirror Specs Focal Lens Diameter: 18 mm Focal Length: 2 in. (50.8 mm) Mirror Diameters: 25 mm Package Includes 1 x Laser Engraver Machine 1 x Water Pump 1 x Storage Tank 1 x Ethernet to Ethernet Cable 1 x Grounding Wire 1 x Venting Exhaust Duct (4 ft. max. length) 2 x Water Hoses 1 x USB Type-A to Type-A Cable 1 x USB Drive with Software 1 x Stainless Steel Clamp 10 x Hex Wrenches 1 x Double-sided Tape 1 x Power Cord 1 x Accessory Bag 2 x Keys 1 x Silicone Sealant 1 x Instruction Manual Laser Tube Lifetime: 80W CO2 laser tube with an estimated lifetime of up to 8,000 operation hours depending on power setting usage and water cooling performance PLEASE NOTE: Frequent use of high laser power settings will shorten the laser tube lifetime as follows: Low Power 10–40% = 7,000–8,000 Hours Moderate Power 40–70% = 5,000–6,500 Hours High Power 70–100% = 3,000–4,000 Hours Compatible Materials: Laser Cutting: Acrylic *Wood Leather Plastics Fabrics MDF Cardboard Paper Corian Foam Fiberglass Rubber Marking/Engraving: Acrylic Wood Leather Plastics Fabrics Glass Rubber Cork Brick Granite Marble Tile River Rock Bone Melamine Phenolic *Aluminum *Stainless Steel *Titanium Cannot cut hardwoods like mahogany CO2 lasers only mark bare metals when anodized or treated. Contact us with questions on specific materials not listed, we can process a sample for confirmation. Some PVC-based acrylics can create toxic fumes when lasered. Warranty: No need to worry! We offer a 1-year parts warranty on all machines. 3-month warranty on laser tubes and laser power supplies 80W and up Certifications: FDA Compliant CE Certification ISO9001 Quality Certification On Aug 24, 2023 at 22:44:06 PDT, seller added the following information:

Returns Accepted for this item if it's within 30 Days